1997 oldsmobile achieva oil pan removal
Answers: 1
Views: 909
Rating: 0
Posted: 11 years ago
The oil pan is located at the bottom of the engian. There will be a lot of screws all around the pan. On the pan will be a plug. Take a wrench or socket and remove the plug. Put a pail or something to catch the oil when you remove the plug. After it has drained, remove all the bolts holding the pan on. You may have to use a screw driver or putty knife and go around the pan to lostenit after you get the bolts out. Drop the pan and take the putty knife and scrape off the old gasket material from the engian and the pan. Be careful not to dig the metal as this could cause a leak spot. Make sure you have a new gasket to put on before you take the old one off. Put the new one on the pan and hold it up to the engian and make sure all the holes line up and start putting the bolts back in. Be sure not to tighten them too much, just snug good. They break if too much pressure is put on them. Make sure the drain plug is snug also after it is put together. Good luck. If the oil pan still wont come out you may have to jack up the engian a little.
Rating: 1
Posted: 11 years ago
how do you change a out of state liscenise to texas and tags
Answers: 2
Views: 410
Rating: 0
Posted: 11 years ago
I would try going to the Texas DMV and doing it there, or give them a call and ask them the right way to do it.
Rating: 1
Posted: 11 years ago
When I try to sign in and enter my email address, it keeps saying to please entr a valid email address. Now what?
Answers: 2
Views: 410
Rating: 0
Posted: 11 years ago
Best thing I did was went to where it says ...forgot password and went in and they emailed me and I made a new password and used my same email address.
Rating: 1
Posted: 11 years ago
kenmore elite top load washer will not spin error code "LF"
Answers: 1
Views: 316
Rating: 0
Posted: 11 years ago
FL means the analog pressure sensor is out of range. This could be caused by a problem with the air pressure hose connection between the bottom of the washer tub and the machine control board. check the tube , probably clear plastic tubing going from the bottom of the tub to the board. Check and make sure it is not pluged or kinked. If it is ok then your problem is the control board and it will need to be replaced. Good luck
Rating: 1
Posted: 11 years ago
locate the fuse in a magic chef microwave model MCD1611B please
Answers: 1
Views: 1017
Rating: 0
Posted: 11 years ago
Remove the cabinet. Usually a few screws hold it on. Now follow the power cord into the back of the oven and it should take you right to the fuse. Usually located about 3 inches in. Its an easy job. Make sure you have the power cord unplugged. Good luck.
Rating: 1
Posted: 11 years ago
what is a code for a philips tv?
Answers: 1
Views: 520
Rating: 0
Posted: 11 years ago
I did this once before. I presume you want the codes so your remote control will work with your tv. The Philips codes are "03" , "04" , "06" and "12". One of these should work. Do you know how to do it.?
Rating: 0
Posted: 11 years ago
How to buy advance Sports Events tickets?
Answers: 2
Views: 1290
Rating: 0
Posted: 11 years ago
You might try TICKETS .COM
Rating: 0
Posted: 11 years ago
WHERE IS THE DLP CHIP LOCATED ON A SAMSUNG HLT6756WX/XAA TV SET?
Answers: 1
Views: 1597
Rating: 0
Posted: 11 years ago
I'm guessing you have white specks all over your screen. I went through the same thing. I have a Samsung too. Take the back cover off the set. Now look for the cooling fan. Should be right there in view. Now look directly in where the fan is blowing the air. Should be right in front of it. You will have to remove the fan and a few other wires{ mine were just the kind that plug in.} and get them out of the way. then you will be at the dlp holder. You will have to remove this to get into the chip. The chip is about a 2x2x1/4 inch squairof steel with a piece of squair glass in the middle. This is your chip. There should be some numbers on it. These are what you look for when you order the new one. I got mine through Ebay. Type in DLP CHIP and the number. Go mine from SHOPJIMMY on Ebay. Be careful Putting it back in. Don't put the fan back in until you have the chip lined up. You have to turn on the tv and see if the picture is lined up with the screen. DON'T LEAVE THE TV ON FOR ONLY A MIN> OR SO> Just long enough to see the pic. Plug every thing in but don't bolt the fan down. You will have to adjust the chip just a fraction of an inch or so. If I had it here I could do it in 5 mins. Good Luck.
Rating: 0
Posted: 11 years ago
Does anyone know where I can download an owner's manual for a Magellan Roadmate X13-12056 GPS?
Answers: 1
Views: 3253
Rating: 0
Posted: 11 years ago
Just type in The name and model and model number and it will take you to a site that has several. I just did it.
Rating: 0
Posted: 11 years ago
singer 5500 instruction manual
Answers: 1
Views: 173
Rating: 0
Posted: 11 years ago
Go to : www. Singermachines.co.uk/indstbooks.htm ...............I just looked this up and they say its a free download. You might want to have a printer handy. Good luck.
Rating: 0
Posted: 11 years ago