close
    after doing a head job on2001 isuzu rodeo 3.2 it will only run if i unplug the tps senor but it reduces engine power HELP PLS

    0  Views: 521 Answers: 1 Posted: 11 years ago

    1 Answer

    How to troubleshoot a TPS sensor 


    Voltmeter
    Two pins


    Instructions
    1
    Open the hood of your vehicle and locate the TPS in the engine compartment. Its most common location is on the outside--to the right or left--of the throttle body or carburetor plate shaft. Here you will see a small black box with three wires coming out from its electrical connector.


    2
    Unplug the TPS electrical connector. Turn on the ignition switch, but do not start the engine. Using a voltmeter, probe the connector’s terminals coming from the computer side to test for supply voltage. Touch the negative lead to the connector’s terminal ground--most likely the black wire--and the meter’s positive or red lead to the connector’s terminal reference voltage wire, a blue or gray color wire. Your meter should read a steady 5.0 volts at the terminal. If you don’t receive this voltage reading, there is an open or short in the supply wire. Turn off the ignition switch and plug the electrical connector back to the TPS.


    3
    Test the TPS for signal voltage to the computer. Insert a pin through the ground wire and another pin through the signal voltage wire and connect the voltmeter probes to the pins using alligator clips. Start the engine. As you manually open and close the throttle plate, watch the voltage readings at the meter. The voltage should gradually increase from 1 to 5 volts and back to 1 volt. If you see erratic movement or no movement of voltage signal, replace the TPS. Turn off the engine.


    4
    Test the TPS’ resistance. This is an alternate method to test a TPS equipped with a variable resistor. Unplug the TPS electrical connection. Set your multimeter to ohms. Connect the ohmmeter probes to the sensor’s supply and signal wire contacts. Manually open and close the throttle plate and watch the resistance reading at the meter. The resistance should gradually increase and decrease as you open and close the throttle plate. If there is an erratic resistance change, no change, or no resistance at all, replace the TPS.


    5
    Adjust the TPS. Some sensors need to be adjusted from time to time. They are mounted with a couple of screws that allow the sensor to be rotated for adjustment. Loosen the mounting screws. With the ohmmeter connected as described in Step 4, rotate the sensor until you obtain the resistance specified in your vehicle service manual. Tighten the mounting screws and check the sensor’s resistance as described in Step 4.


    6
    Plug in the TPS electrical connector, start your engine and test for performance.


    Read more: How to Troubleshoot a TPS sensor | eHow.com http://www.ehow.com/how_4489318_troubleshoot-tps-sensor.html#ixzz2KC4MLjEw



    Related Questions In This Category
    How does the process of scrap car removal work in Auckland?
    Answers: 0 | Views: 14 | Rating: 0 | Posted: 1 day ago

    Top contributors in Other - Cars & Transportation category

     
    ROMOS
    Answers: 85 / Questions: 0
    Karma: 4320
     
    Colleen
    Answers: 176 / Questions: 0
    Karma: 2955
     
    jhharlan
    Answers: 38 / Questions: 0
    Karma: 2730
     
    country bumpkin
    Answers: 36 / Questions: 0
    Karma: 2340
    > Top contributors chart

    Unanswered Questions

    thammysaomai
    Answers: 0 Views: 12 Rating: 0
    sunwin77co
    Answers: 0 Views: 16 Rating: 0
    bossnhacaicom
    Answers: 0 Views: 16 Rating: 0
    zulystorevn
    Answers: 0 Views: 15 Rating: 0
    me8dayvn
    Answers: 0 Views: 14 Rating: 0
    > More questions...
    453068
    questions
    720020
    answers
    757742
    users