HI THERE ARE 29.922 US QUARTS IN ONE CU FT OR 24.9154 IMP QUARTS IN ONE CU FT
DIVIDE YOUR REQUIRED QUARTS 380 / 29.922 = 12.700 CU FT US OR
380 / 24.9154 = 15.252 CU FT IMP
HOPE THIS HELPS
MONDEOMAN
HI YOU HAVE SOME THING WRONG WITH YOUR QUESTION AS YOU CAN NOT HAVE LIQUIDS AS CM I ASSUME YOU MEAN CENTI -LITRES
SO YOU HAVE A TANK 4M X 3M WITH 7200000CENTI-LITRES OF WATER
THERE FORE LENGTH X WIDTH X HEIGHT = VOLUME
HI YOU HAVE SOME THING WRONG WITH YOUR QUESTION AS YOU CAN NOT HAVE LIQUIDS AS CM I ASSUME YOU MEAN CENTI -LITRES
SO YOU HAVE A TANK 4M X 3M WITH 7200000CENTI-LITRES OF WATER
THERE FORE LENGTH X WIDTH X HEIGHT = VOLUME
HI TO FIND THE SQ ROOT OF A NUMBER IS THE OPPOSITE OF THE SQ OF A NUMBER IE:
100 THE SQ ROOT IS 10 THE SQ ROOT OF A NUMBER IS A NUMBER WHICH MULTIPLYED BY ITSELF GIVES YOU THE ORIGINAL NUMBER
EXAMPLES 9 SQ ROOT = 3 AS 3 X 3 = 9 49 SQ ROOT = 7 AS 7 X 7 =49
THESE ARE EASY EXAMPLES FOR MORE COMPLICATED NO'S YOU WILL NEED A CALCULATOR OR MATHS TABLES BOOK
HOPE THIS HELPS
MONDEOMAN
HI IT IS A SEQUENTIAL SEQUENCE using the square of the answer
START WITH 2 square it = 4 square it = 16 square it = 256 square it = 65536 and so on
HOPE THIS HELPS
MONDEOMAN
HI THERE ARE 6.35 mm IN 1/4 INCH
HOPE THIS HELPS
MONDEOMAN
HI IT IS IMPOSSIBLE TO CALCULATE AN ACCURATE MPH WITH OUT FRICTION COEFICIANTS ETC BUT AN APPROX FIGURE CAN BE CALCULATED AS FOLLOWS
WORK OUT THE VOLUME PER MIN IN YOUR PIPE MULTIPLY BY 60 TO MAKE IT PER HR THEN DIVIDE BY 5280 TO MAKE IT MPH
IE: 1.25 X Pi = 1.25 X 3.14159 =3.9269 sq in = 0.32724 sq ft
DIVIDE THIS INTO 125/0.32724 = 381.98 FT PER MIN X 60 =22918.958 FR PER HR
DIVIDE BY 5280 WHICH IS FT IN MILE 22918.958/ 5290 = 4.3407 mile per hr
ASSUME YOUR SMALL NOZZLE IS 1/4inch dia
1/4 X 3.14159 = 0.786 sq in = 0.0655 sq ft 125/.0655 = 1908 ft per min x 60 =114480ft per hr divide by 5280 114480/5280 = 21 mile per hr approx
AS I HAVE ALREADY STATED THIS IS A VERY CRUDE APPROXIMATION AS THERE ARE A LOT OF VARIABLES WHICH HAVE TO BE TAKEN INTO ACCOUNT
HOPE THIS HELPS
MONDEOMAN
HI
The compression ratio is a single number that can be used to predict the performance of any internal-combustion engine. Basically its the volume of the cylinder at full intake to the volume at full compression.
The ratio is calculated by the following formula:
, where
b = cylinder bore (diameter)
s = piston stroke length
Vc = volume of the combustion chamber (including head gasket). This is the minimum volume of the space into which the fuel and air is compressed prior to ignition. Because of the complex shape of this space, it usually is measured directly rather than calculated.
Due to pinging (detonation), the CR in a gasoline/petrol or LPG or CNG-powered engine will usually not be much higher than 10:1.
In engines with a ping sensor and an electronic control unit, the CR can be as high as 12.5:1 (2005 Audi A6 3.2)
In a turbo charged or super charged engine the CR will be around 8.5:1
In a diesel engine the CR will be 20:1 and higher.
I HOPE THIS EXPLAINS CR OK FOR YOU IF YOU WANT FURTHER INFO LOG ONTO GOOGLE SEARCH ENGINE AND ASK YOUR QUESTION THERE WILL BE THOUSANDS OF SITES EXPLAINING IT IN MORE DETAIL
HOPE THIS HELPS
MONDEOMAN
HI
An annotation is a note that is made while reading any form of text. This can be as simple as underlined or highlighted passages.
IF YOU LOG ONTO GOOGLE SEARCH ENGINE AND ASK THE QUESTION YOU WILL GET A MORE DEFINATIVE ANSWER
I HOPE THIS HELPS
MONDEOMAN
HI IF YOU MEAN 6.28CU MTRS THEN THERE ARE A 1000 LITRS PER CU MTR
THEREFORE 6.28 X 1000 = 6280 LTR
IF YOU MEAN 6.28 X 6.28 X 6.28 = 247.673 CU MTRS = 247.673 X 1000 = 247673.15 LTRS
I HOPE THIS HELPS
MONDEOMAN