close
Answers: 209
freon capacity of 2011 Ford Fusion
Answers: 1 Views: 2425 Rating: 1 Posted: 12 years ago

it is .62kg (22oz) or 1.38lb

Rating: 1 Posted: 12 years ago
how can I determine the correct timing mark on the camshaft of 1994 Isuzu rodeo, there are 4 mark on the face of the gear , two v notch are 180 degree aprt and a line at 90 degree
Answers: 1 Views: 623 Rating: 0 Posted: 12 years ago

need engine size. is it 2.6 or 3.2

Rating: 0 Posted: 12 years ago
how many tablespoones to an ounce
Answers: 1 Views: 483 Rating: 0 Posted: 12 years ago

it is 2 tablespoons per ounce.

Rating: 0 Posted: 12 years ago
what is 35% of $7,038.07
Answers: 2 Views: 521 Rating: 1 Posted: 12 years ago

it is about 2,465 or take 7038 X .35

Rating: 1 Posted: 12 years ago
ecu fuse circuit 1996 astro v-6
Answers: 1 Views: 354 Rating: 0 Posted: 12 years ago

it is in the under-hood fuse block 20amp location F7 is the ecm-1.

Rating: 1 Posted: 12 years ago
what is the firing order of 1991 honda accord
Answers: 1 Views: 662 Rating: 1 Posted: 12 years ago

it is 1342

Rating: 1 Posted: 12 years ago
how to replace brake calipers on a 1997 mercury villager
Answers: 2 Views: 1717 Rating: 1 Posted: 12 years ago

Home | Account | Contact ALLDATA | Log Out | Help YATES AUTOMOTIVE SERVICE
YATES AUTOMOTIV00003

Select Vehicle | New TSBs | Technician's Reference Component Search:

Conversion Calculator

1997 Mercury Truck Villager V6-181 3.0L SOHC VIN 1 EFI

Vehicle Level Brakes and Traction Control Disc Brake System Brake Caliper Service and Repair Removal and Installation

Removal and Installation

REMOVAL

Raise and support the vehicle.Remove the wheel and tire assembly.Mark the front disc brake caliper to ensure it is installed on the correct front wheel knuckle.

Remove the banjo bolt and copper washer. Discard the copper washer.

Brake Caliper Bolts

Use a Torx(R) T40 bit to remove the two brake caliper bolts.Remove the front disc brake caliper from the front disc brake rotor.

INSTALLATION

Use a C-clamp and a used brake shoe and lining to retract the caliper piston fully in the piston bore. Install the front disc brake caliper over the front disc brake rotor with a rotating motion. Ensure that the inboard and outboard front brake shoes and linings are properly positioned.

NOTE: Ensure that the correct front disc brake caliper, as marked during removal, is installed on the correct front wheel knuckle. The bleeder screw should be positioned on the top of the front disc brake caliper when installed on the vehicle.

Lubricate the stainless steel locating pins with Silicone Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A.Install the brake caliper bolts. Tighten the brake caliper bolts to 24-34 Nm (18-25 ft. lbs.).Install the banjo bolt and new copper washer. Tighten the banjo bolt to 17-20 Nm (12-14 ft. lbs.).Fill the brake master cylinder reservoir with Ford High Performance DOT 3 Brake FluidC6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.Bleed the brake system.Install the wheel and tire assembly. Tighten the lug nuts to 98-118 Nm (72-87 ft. lbs.).Lower the vehicle.Road test the vehicle.

© 2012 ALLDATA LLC. All rights reserved.
Terms of Use

Rating: 2 Posted: 12 years ago
1992 chevy 4x4 pickup 350 engine code 43 what do i fix
Answers: 2 Views: 452 Rating: 1 Posted: 12 years ago

code 43 indicates that a malfunction in the electronic cotrol circuit is present. it is hard to test an ignition module but most of the times the problem is the ignition module in the distribuitor in not allowing the engine computer to take over the advancing or retarding of the ign. timing. aside from you doing a visual check of the wires going to the distribuitor , you can assume that the ignition module is the most likely problem.

Rating: 1 Posted: 12 years ago
1992 chevy 4x4 pickup 350 engine code 43 what do i fix
Answers: 2 Views: 452 Rating: 1 Posted: 12 years ago

code 43 indicates that a malfunction in the electronic cotrol circuit is present. it is hard to test an ignition module but most of the times the problem is the ignition module in the distribuitor in not allowing the engine computer to take over the advancing or retarding of the ign. timing. aside from you doing a visual check of the wires going to the distribuitor , you can assume that the ignition module is the most likely problem.

Rating: 1 Posted: 12 years ago
1500mg equals how many teaspoons
Answers: 1 Views: 524 Rating: 1 Posted: 12 years ago

it is 3 teaspoons

Rating: 1 Posted: 12 years ago

Top Contributors

 
ROMOS
Answers: 39019 / Questions: 245
Karma: 2300K
 
Colleen
Answers: 90249 / Questions: 368
Karma: 2042K
 
country bumpkin
Answers: 26279 / Questions: 276
Karma: 1665K
 
Benthere
Answers: 4136 / Questions: 80
Karma: 1556K
> Top contributors chart
452236
questions
719700
answers
754009
users