close
Answers: 209
2500mg equal how many grams
Answers: 1 Views: 555 Rating: 1 Posted: 11 years ago

is it 250 grams.

Rating: 1 Posted: 11 years ago
how do i bleed the coolant system on a 2000 grand am v6
Answers: 1 Views: 357 Rating: 0 Posted: 11 years ago

there are two bleeding screw on the engine that look like brass in color. open  the one above the water pump while the engine is running and wait until all air is out and then do the same with the second one on the thermostat housing. for me i tend to remove one of the heater hoses off until coolant comes out. it is a little faster this way.

Rating: 2 Posted: 11 years ago
SUBARU motor crank shaft inspection DO I have to split crankase
Answers: 1 Views: 484 Rating: 1 Posted: 11 years ago

yes you do. the case contains the crank and any damage there will need a bolck.

Rating: 1 Posted: 11 years ago
how to replace brake calipers on a 1997 mercury villager
Answers: 2 Views: 1716 Rating: 1 Posted: 12 years ago

Home | Account | Contact ALLDATA | Log Out | Help YATES AUTOMOTIVE SERVICE YATES AUTOMOTIV00002

Select Vehicle | New TSBs | Technician's Reference Component Search:

Conversion Calculator

1997 Mercury Truck Villager V6-181 3.0L SOHC VIN 1 EFI

Vehicle Level Brakes and Traction Control Disc Brake System Brake Caliper Service and Repair Removal and Installation

Removal and Installation

REMOVAL

Raise and support the vehicle.Remove the wheel and tire assembly.Mark the front disc brake caliper to ensure it is installed on the correct front wheel knuckle.

Remove the banjo bolt and copper washer. Discard the copper washer.

Brake Caliper Bolts

Use a Torx(R) T40 bit to remove the two brake caliper bolts.Remove the front disc brake caliper from the front disc brake rotor.

INSTALLATION

Use a C-clamp and a used brake shoe and lining to retract the caliper piston fully in the piston bore. Install the front disc brake caliper over the front disc brake rotor with a rotating motion. Ensure that the inboard and outboard front brake shoes and linings are properly positioned.

NOTE: Ensure that the correct front disc brake caliper, as marked during removal, is installed on the correct front wheel knuckle. The bleeder screw should be positioned on the top of the front disc brake caliper when installed on the vehicle.

Lubricate the stainless steel locating pins with Silicone Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A.Install the brake caliper bolts. Tighten the brake caliper bolts to 24-34 Nm (18-25 ft. lbs.).Install the banjo bolt and new copper washer. Tighten the banjo bolt to 17-20 Nm (12-14 ft. lbs.).Fill the brake master cylinder reservoir with Ford High Performance DOT 3 Brake FluidC6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.Bleed the brake system.Install the wheel and tire assembly. Tighten the lug nuts to 98-118 Nm (72-87 ft. lbs.).Lower the vehicle.Road test the vehicle.

© 2012 ALLDATA LLC. All rights reserved.
Terms of Use

Rating: 2 Posted: 11 years ago
What should be the voltage of a gas pump in a 2004 volkswagon GTI 1.8?
Answers: 1 Views: 378 Rating: 1 Posted: 11 years ago

with the key on , you should see battery voltage at the fuel pump or about 12 volts. have a test light or volt meter is better to the fuel pump 12v wire and see if you have battery voltage for about 2 seconds with key on and also while cranking. most of the time it will be the fuel pump at fault. hardly ever the relay or eng. control module. 

Rating: 2 Posted: 11 years ago
Where are the predator drones the US military in Afghanistan controlled from?
Answers: 7 Views: 870 Rating: 0 Posted: 11 years ago

i still do not have the answer to that riddle. i have tried all of the answers that were suggested but no luck. i am looking for it.

Rating: 7 Posted: 11 years ago
Where are the predator drones the US military in Afghanistan controlled from?
Answers: 7 Views: 870 Rating: 0 Posted: 11 years ago

somewhere near Las Vegas, Nevada. it is done from about 6,000 miles away. this is an amazing ability.

Rating: 8 Posted: 11 years ago
what might cause a hole in a 2003 ford explorer valve cover
Answers: 1 Views: 352 Rating: 1 Posted: 11 years ago

it may be caused by a leaking egr valve pipe that on some ford 4.0 engines crosses the valve cover .

Rating: 1 Posted: 11 years ago
how do I fix a loose wire for my 1998 ford contour right turn signal
Answers: 1 Views: 429 Rating: 0 Posted: 12 years ago

with a test light you check for power and ground. this will eliminate the guess work and it will tell if the socket is the problem or a wire problem.

Rating: 1 Posted: 12 years ago
what are the engine bolt torch specs for my 2.2 ltr camry
Answers: 1 Views: 406 Rating: 1 Posted: 12 years ago

it is 36ft lbs plus 90degrees

Rating: 1 Posted: 12 years ago

Top Contributors

 
ROMOS
Answers: 39019 / Questions: 245
Karma: 2300K
 
Colleen
Answers: 90249 / Questions: 368
Karma: 2042K
 
country bumpkin
Answers: 26279 / Questions: 276
Karma: 1665K
 
Benthere
Answers: 4136 / Questions: 80
Karma: 1556K
> Top contributors chart
452116
questions
719643
answers
753237
users